AC/DC TIG 200 ST IGBT

SKU: 1023-001
GTIN: 4260294080232
Category: AC/DC TIG welders

STAHLWERK AC/DC WIG 200 ST IGBT - combined inverter welder with 200 Ampere TIG & ARC MMA, aluminium welding, white, 7 years manufacturer warranty

449,00 €

incl. 19% VAT , plus

Instead of: 579,00 €

(Save 22.45%, i.e. 130,00 €)

Available immediately
Delivery time: 1 - 2 Workdays (Other countries)

Device Funktions & Components

AC/DC TIG welding – Alternating current (AC) and direct current (DC). welding and cutting of almost all materials such as steel, stainless steel, aluminium, copper and many more.
2 in 1 combined device – TIG and MMA welding up to 200A.
IGBT Technology – latest transistor technology enables highest power and a duty cycle of 60% at full power. No transformer, no MOSFET, modern IGBT.
Lightweight & compact design – only 11,5 kg and dimensions of 455 x 220 x 370 mm. Innovative IGBT transistors save space and weight compared to the old MOSFET technology. No heavy carrying!
High frequency ignition– allows non-contact ignition and ensures a much better welding result.
Smart cooling & overheating protection – modern technology, built-in overheat protection and high-performance cooling allow you to get maximum Performance.

Device Features & Benefits

2T/4T (TIG) – determines the control of the operating mode and provides extended control over the current flow. In 2T mode, high-frequency ignition (HF) remains active until the button on the torch is released. In 4T mode the arc is ignited after a single press and release of the button. After pressing and releasing again, the ignition is stopped.
End Current – prevents voids (end craters) at the end of the weld.
Gas pre- and -post flow (TIG) – protects the tungsten electrode against excessive wear and protects the weld from oxidation. The parameters can be set individually and separately. They indicate how long before and after ignition gas should flow.

AC - Balance (TIG) – is a variable setting between breaking the oxide layer (-) and deeper penetration (+). This helps to influence properties of different materials and alloys.

Hotstart – Automatic voltage increase upon the start for better ignition results.
Anti-stick - Automatic shutdown of the welding current in case of sticking of the electrode which allows an easy removal. It also prevents annealing of the electrode.
TIG (Tungsten-Inert-Gas) – Inert gas welding with inert / inactive gases such as Argon 4.6 (99.996%). An arc is created in an argon bell between the tungsten electrode and the workpiece. This melts the material and any filler material that is supplied. A weld seam is created.
MMA / Stick electrode welding– is a universal welding process. No protective gas is needed and can therefore be used flexibly anywhere.
Note:
- The unit is not intended for use in residential areas where power is supplied by a public low-voltage power supply system. It may be difficult to ensure electromagnetic compatibility in these areas due to both conducted and radiated interference.

Technische Daten

Output current	30-200 A
Duty Cycle	60 % at 200 A / 100 % at 126 A
Protection type	IP21S
Insulation class	F
Power supply	230 V AC (+-15%) / 1 ~ (single phase)
Frequency	50/60 Hz
Maximal power input	41,7 A
Actual power input	26,4 A
Weight	11,5 kg
Dimensions L x W x H (mm)	455 x 220 x 370
Mains connection	SchuKo-Bauart CEE 7/7
Standards	IEC 60974-1; EN 60974-10 (Class A)

Lieferumfang

The STAHLWERK AC/DC TIG 200 ST IGBT welding device
TIG Torch Package "WP-26F" 4,5 meters* with flexible torch head and bend protection at the gas connection
TIG accessory set, 8-pieces*:
- 3x gas nozzles in sizes: 5, 6, 7
- 1x collet size 1,6
- 1x collet body size 1,6
- 2x back caps (a long and a short each)
- 1x universal tungsten electrode
*Pre-assembled accessory on the picture of the welding torch is part of the 8-piece set
Ground cable 5 meters
Electrode holder 5 meter
Chipping hammer
Wire brush
Gas hose with snap-on quick coupling 5 meters
UK 3-Pin sockets adapter (included to UK customers with UK shipping address)
Protection cover

Note: The units of the latest generation may contain details that differ from the product images shown here. In the new design, the STAHLWERK lettering and the reference to the IGBT technology are omitted, as this is now installed as standard. We will update the pictures as soon as possible.

High-quality professional WP-26F TIG hose package with flexible torch head and bend protection at the gas connection. Optimal ignition behavior up to 200 A. Thicker hose and ergonomic handle. A 8-part set of consumables for immediate start is included in delivery.

Robust electrode holder with modern 9 mm connection and 25 mm² cable cross-section. Best conductivity through high quality copper cables. Different angles for stick electrodes possible.