STAHLWERK MIG MAG 200 Double Pulse Pro full-synergic welder with 200 Amp and AK25/MB25 welding torch

https://img.youtube.com/vi/47lNESzotOI/default.jpg

https://img.youtube.com/vi/NkUuV_iRA8Q/default.jpg

https://img.youtube.com/vi/sqwxCYaqrBM/default.jpg

STAHLWERK MIG MAG 200 Double Pulse Pro full-synergic welder with 200 Amp and AK25/MB25 welding torch

SKU: 1221
GTIN: 4260294082212
Category: Sale

The powerful STAHLWERK MIG 200 Double Pulse Pro shielded arc welder has a convenient pulse as well as double pulse function and works with up to 200 amps. The special double pulse function enables clean, precise welding of thin sheets. The double pulse function is particularly useful when processing aluminum, as the welding current is controlled in optimum synchronization with the wire feed and the oxide layer is broken up cleanly. The finely regulated control of the temperature produces an optimum penetration for the formation of a defect-free weld seam without pores. Another advantage of the robust 17.25 kg combination welder is that it can also be used for E-Hand/MMA welding.

899,99 €

incl. 19% VAT , plus

Old price: 1.030,09 €

Available immediately
Delivery time: 1 - 3 Workdays (DE - int. shipments may differ)

You can purchase a maximum of Units 3 of this item.

Functions

Extensive double pulse function in MIG welding prevents burning through materials at low root heights and reduces deformation due to heat. Therefore, the MIG 200 double pulse Pro welder is especially suitable for welding thin plates and materials that may be heated only slightly.
The MIG 200 Double Pulse Pro operates on the basis of an advanced IGBT module with the latest inverter and control technology.
The MIG 200 double pulse Pro welding machine can process and weld non-, low- and high-alloy steels such as steel, stainless steel and aluminum alloys.
Thanks to the pulse function and advanced torch ergonomics, welding can be performed in all known joint shapes (butt welds and fillet welds) and positions (standing seam, drop seam, transverse seam).
Convenient selection of twin, spot and continuous spot operating modes as well as other special welding functions.
The welding unit is suitable for use with solid welding wire (steel, stainless steel; ø 0.8 - 1.0 mm and aluminum; ø 1.0 - 1.2 mm) and flux-cored wire. Thus, a wide variety of materials can be processed and welded.

Features & Advantages

Universally applicable 3 in 1 combination unit. MIG, MAG and MMA welding is possible up to 200 amps.
Built-in safety function to reduce the voltage (Volt Reduction Device - VRD). To increase safety during welding, the open circuit voltage U0 is reduced to 14 volts in MMA mode. The welder automatically detects the start of the welding process and then increases the open circuit voltage up to 62 volts. VRD is factory preset and cannot be turned off.
Built-in job memory allows preferences and parameters to be set to complete recurring jobs efficiently and quickly. Jobs and parameters can be restored. This enables convenient work without spending a lot of time on set-up times.
2T/4T (MIG) mode allows control of the operating mode and provides advanced control over current flow in Special 2 and Special 4 cycle modes.
Automatic wire feed for precise regulation of wire feed speed in direct relation to the set welding current.
Extensive setting options in terms of current and functions via intuitive graphic interface in the display.

Highest Efficiency & Power - Single-phase AC power (230 V) supplies the unit and allows output power of true 200 amps.
Smart Cooling & Overheat Protection - State-of-the-art technology, built-in overheat protection, and high-performance cooling allow for maximum power retrieval during welding.
Suitable for use with the following shielding gases: 100% Ar, 100%_CO2, 2%_{CO2 +} 98% Ar, 20%_CO2₊ 80% Ar. This ensures efficiency, energy saving as well as strong arc penetration with low welding deformations.
The spool mandrel ensures frictionless acceptance of 50 mm wire spools and is not suitable for 1 Kg wire spools with 16 mm spool mandrel acceptance.

Note: The unit is not intended for use in residential areas where power is supplied by a public low-voltage power system. It may be difficult to ensure electromagnetic compatibility in these areas due to both conducted and radiated interference.

Technische Daten

Output current MIG / MIG pulse / MMA	50 -200 A (MIG) / 30 - 170 A (MIG pulse) / 20 - 180 A (MMA)
Protection class	IP21S
Mains voltage	1 x 230 V AC (+- 15%)
Mains frequency	50/60 Hz
Maximum mains current (_I1max)	38 A
Maximum effective mains current (_I1eff)	14,7 A
Open circuit voltage (U0)	62 V
Weight	17,25 kg
Dimensions L x W x H (mm)	590 x 240 x 430 mm
Mains connection	CEE 7/7 Schuko plug
Standards	IEC 60974-1; EN 60974-10 (Class A)

Lieferumfang

1 x STAHLWERK MIG 200 double pulse Pro
1 x Professional MIG welding torch AK-25 / hose package 3 meters with Euro central connection.
1 x 3-piece MIG accessory set (already pre-assembled on the MIG/MAG torch)
- 1 x gas nozzle
- 1 x contact tip 0.8 mm
- 1 x gas nozzle holder
1 x gas connection hose with quick coupling 3 meters
1 x earth cable 3 meters (25 mm² with 13 mm mandrel)
1 x contact tip M6 x 28 x 0.8 mm
1 x contact tip M6 x 28 x 1.0 mm
2 x wire guide rollers 0.8 & 1.0 mm with V-profile for steel (already installed in the device)
2 x wire guide roller 1.0 & 1.2 mm with U-profile for aluminum
1 x wire brush
1 x installation wrench
1 x protective cover